Goldchaser1
dave
Oh dam,used mine hard in the pilbara this year to push into spinafex and scrub,will check them this arvo 
Minelab GPX6000 coil issues
Help Support Prospecting Australia:
Just checked mine. No cracks so far.
And I've used it a lot so far this year.
And I've used it a lot so far this year.
Goldchaser1
dave
Yeah same here SL,all ours are ok,maybe one just starting on the bosses 11 but not a problem atm,i remember using the 17 like a whipper snipper in one spot this year,i was worried phewwww
Yeah, I tend to move a few of the lighter materials around.Yeah same here SL,all ours are ok,maybe one just starting on the bosses 11 but not a problem atm,i remember using the 17 like a whipper snipper in one spot this year,i was worried phewwww
Mine has a bit of a loose shift though. No matter how much I've tried to tighten it.
I've given up and will take it back to the store I got it from.
Goldchaser1
dave
The yoke rubbers worn or shaft twisting?
After reading the thread, I thought about the first time that my detector was removed from the box. The first thing that came to mind was the very thin lugs on the coil compared to every other coil that I have owned. Itās a natural consequence of pushing limits of design to achieve bragging rights in relation to weight. In open country with very few obstructions, this design should do a reasonable job. Unfortunately, this is not always the case. Fatigue caused by subtle lateral movement of the lugs will eventually lead to cracking and the eventual failure of the mechanism. If the issue arises on a regular basis, I would hope that design modifications would be put in place to address the problem. If you look at the new Nuggetfinder coils for the 6000, there appears to be more āmeat on the bonesā in this area. Rohan is very good in designing strong and reliable coils. Hopefully this trend will continue with the Xceed range. With another company now producing a detector that appears to show some potential, competition should lead to design innovation and improvement.
PS. Just checked my 11ā and noticed hairline cracks in the same areas as Northeastās coil.
PS. Just checked my 11ā and noticed hairline cracks in the same areas as Northeastās coil.
Not sure what's going on. When it's fully tightened and the coils on the ground and a bit of pressure is put downwards the bottom connection has a bit of play in it.
Goldchaser1
dave
Not sure if your saying your rubbers are worn or the yokes lose in the shaft SL?
If the yokes loose just pull it out,get all the old glue off it,sand it up with coarse paper,i even lightly wire wheel them on the shafts i put togethor,sand the inside of the shaft with about 60 or 80 paper lightly(roll the paper so it fits in the shaft),mix up some 24hr araldite,smother the yoke with it,twist it about a bit as ya put it in so the epoxy spreads etc,clean up the excess,tape the join with elect tape and stand it up onight so the epoxy stays at the bottom,if ya key both surfaces up correctly it is a very strong bond.
I think the coils are a bit weak around that area but also im sure where all guilty of it and i know i am,as those rubbers wear we just keep nipping the coil bolt up,instead of replacing the rubbers,no prizes for guessing what's goin on there,as lesgold says there's a price for pushing the boundaries on weight....
Goldchaser1
dave
Under the yoke rubbers there is a pressed in bush,it does wriggle or allow flex,noticed this a while ago,i just had a look at a new 14 we have here and with new rubbers on a shaft it actually spreads the coils ears a bit,i don't think worn rubbers should cause cracking,my myth busted 
Ya all just gonna have to pony up and buy one of my shafts
Ya all just gonna have to pony up and buy one of my shafts
That bit there where you tighten the shaft. There is a bit of play there when it's fully tightened. May take it apart and have a look tomorrow but I'm not very handy.
Attachments
Have contacted Minelab and the 11" coil will be sent back in the next week or so and have been assured that it will be changed over. Have also been advised that since the original batch there have been changes made so that this does not happen again.
Not great but at least with Minelab you know that warranty issues will be dealt with and it is reassuring to know that things are being done so that the issue isn't simply repeated with the new coil.
Cheers, N.E.
Not great but at least with Minelab you know that warranty issues will be dealt with and it is reassuring to know that things are being done so that the issue isn't simply repeated with the new coil.
Cheers, N.E.
user 22230
Gavin of Garfield
- Joined
- Dec 7, 2021
- Messages
- 998
- Reaction score
- 2,683
Things go wrong but they back their product. 
In this current age one of the few manufacturers that do without having to threaten court action. Well done Minelab I say 
In this current age one of the few manufacturers that do without having to threaten court action. Well done Minelab I say
Same as you NE. Contacted Minelab and I was told to send my coil back. Phoned a mate and suggested that he check his coil. It was cracked in a different part of the lug. He sent his back as well. I was pleased to hear that changes to the design of the coil were implemented to solve the problem. Thumbs up to Minelab for addressing the issue.
- Joined
- Oct 21, 2021
- Messages
- 83
- Reaction score
- 87
Had cracks in my 11".
Replaced under warranty.
Also found cracks on the 14 inch so back it goes.
Replaced under warranty.
Also found cracks on the 14 inch so back it goes.
- Joined
- Jan 27, 2015
- Messages
- 7,768
- Reaction score
- 12,893
Difference I've found is the size/shape is better to manoeuvre in tight or overgrown areas.
I would also say they are better built & probably run a bit smoother (but that could be just surface area related too).
Performance wise I can't fault the stock coils though & feel the 11" gives the smaller aftermarket coils a run for their money for sensitivity. I've had mine since release & haven't had any issues with the stock coils though but realise plenty of others have.
If you don't need a smaller or elliptical coil I'd say save your money.
Yeah because you have piece of mind that they will at least work!
My 2nd minelab 11" coil became touch sensitive today. Was running beautifully, then all of a sudden, useless. Pack up and go home with the *****. For an $8 k machine, they got the coil wrong, cheap and nasty **** box coils.
that is a shame mate. Get onto them.
And yet after all the reported failures, their website has the gall to make this astonishing claim:
